| 7Y1563 CATERPILLAR Slewing bearing for 320L | r, r1,2 min.:0.3 mm; Mass inner ring:0.049 kg; d:40 mm; B:20 mm; F:45 mm; |
| 24100N8102F1 KOBELCO Turntable bearings for SK150LC-III | Basic Dynamic Radial Load Rating C:85200 N; B:28.00 mm; d:120.000 mm; Oil Speed Rating Open/Shielded n2:4000 rpm; Grease Speed Rating Open/Shielded n1:3400 rpm; Basic Static Radial Load Rating Co:80000 N; Accessories:Seal & Snap-Ring; Fillet Radius ra:2.00 mm; D:180.0000 mm; Sealed Speed Rating n3:2 |
| 227-6094 CATERPILLAR Slewing bearing for 345B II | Coefficient of friction µ min.:0.08; Permissible sliding velocity v min.:0 m/s; Tolerance shaft:e7; h:46 mm; a:3 mm; α:124 °; Tolerance housing:H7; Permissible sliding velocity v max.:0.5 m/s; d:45 mm; D:55 mm; Specific dynamic load factor K:25 N/mm²; Mass bushing:0.31 kg; Coefficient |
| AT19077 JOHN DEERE Turntable bearings for 792D | Mass pillow block:13.1 kg; Housing:SAF 515; P150°:25.4 kN; da:60.325 mm; P60°:75.6 kN; Cap bolt recommended tightening torque:81.3 N·m; Cap bolt, SAE grade:5; Pa:5.65 kN; Stabilizing ring:2 x SR-15-0; PG:1/8 NPT; Cap bolt:2 x 1/2-13 UNC; H2:28.575 mm; RG:1/4 NPT; R1:46.038 mm; A1:79.3 |
| PW40F00004F1 CASE Turntable bearings for CX31B | A1:14 mm; N:16 mm; T:54.2 mm; Recommended diameter for attachment bolts, inch G:0.5625 in; Limiting speed:4300 r/min; A3:3.2 mm; Thread grub screw G2:5/16-24 UNF; DN:6.5 mm; J:148.5 mm; H:178.5 mm; Recommended diameter for attachment bolts, mm G:14 mm; Rα:45 °; J6:120.5 mm; Db2:111 mm; SWN:7 mm; |
| 8K4127 CATERPILLAR Turntable bearings for 225B | C1 max.:43 mm; Basic static load rating C0:530 kN; l5 ≈:40 mm; d2 max.:162 mm; Mass rod end:10.5 kg; w:80 mm; Specific dynamic load factor K:100 N/mm²; d4 ≈:92 mm; l4 max.:284 mm; l3 min.:80 mm; α:6 °; Basic dynamic load rating C:315 kN; r1 min.:1 mm; h1:200 mm; B:49 mm; d:70 mm |
| YN40F00004F1 KOBELCO Turntable bearings for SK210LC VI | C:18.824 mm; Cb min.:3 mm; B:21.996 mm; d1 ≈:86.55 mm; Da max.:102 mm; ra max.:3.5 mm; db min.:77 mm; r3,4 min.:1.3 mm; Db min.:105 mm; r1,2 min.:3.5 mm; Limiting speed:6000 r/min; Basic dynamic load rating C:108 kN; rb max.:1.3 mm; D:110 mm; d:63.5 mm; da max.:77 mm; a:20.871 mm; T:22 mm; Ref |
| LP40FU0001F1 KOBELCO Slewing bearing for SK120LC IV | B4:4.75 mm; A5:18 mm; H:124 mm; J6:81 mm; Rα:45 °; Basic static load rating C0:7.8 kN; Mass bearing unit:0.62 kg; A3:3.2 mm; A1:12 mm; A:30 mm; Recommended diameter for attachment bolts, inch G:0.375 in; J:99 mm; s1:26.9 mm; R1:20.5 mm; J7:12 mm; Housing material:Cast iron; d:25.4 mm; Recommende |
| 24100N4118F1 KOBELCO Slewing bearing for K909LC II | d:45 mm; Mass rod end:3.2 kg; dk:60 mm; C1 max.:28 mm; l7 min.:55 mm; r1 min.:0.6 mm; l3 min.:65 mm; Basic static load rating C0:224 kN; d2 max.:104 mm; Specific dynamic load factor K:100 N/mm²; Basic dynamic load rating C:127 kN; w:55 mm; h1:145 mm; α:7 °; d4 ≈:65 mm; B:32 mm; l5 &as |
| 227-6089 CATERPILLAR Slewing bearing for 330C | Specific static load factor K0:45 N/mm²; d:160 mm; a:8 mm; Permissible sliding velocity v max.:0.5 m/s; B:160 mm; α:124 °; Coefficient of friction µ max.:0.15; Permissible sliding velocity v min.:0 m/s; Tolerance shaft:e7; D:180 mm; Coefficient of friction µ min.:0.08; h:162 mm; |
| 24100N8102F1 KOBELCO Slewing bearing for SK150LC IV | Fillet Radius rb:1.00 mm; Oil Speed Rating n2:2100 rpm; B:88.00 mm; Fillet Radius ra:2.50 mm; d:180.000 mm; Basic Dynamic Radial Load Rating C:338000 N; D:280.0000 mm; Grease Speed Rating n1:1300 rpm; Basic Static Radial Load Rating Co:520000 N; |
| LS40F00003F1 KOBELCO Turntable bearings for SK480LC VI | Calculation factor f0:13.8; Reference speed:40000 r/min; Calculation factor kr:0.025; D1 ≈:34.8 mm; Basic dynamic load rating C:9.95 kN; Fatigue load limit Pu:0.212 kN; Da max.:38.8 mm; Limiting speed:26000 r/min; ra max.:0.3 mm; Basic static load rating C0:5 kN; B:12 mm; D:42 mm; da min.:23.2 |
| LC40FU0001F1 KOBELCO Turntable bearings for SK300LC IV | Calculation factor Y1:2.3; Fatigue load limit Pu:335 kN; d3:350 mm; db min.:296 mm; B:146 mm; B4:41 mm; b:16.7 mm; Limiting speed:1300 r/min; ra max.:4 mm; da max.:321 mm; K:9 mm; Reference speed:1000 r/min; Mass bearing + sleeve:115 kg; Da max.:440 mm; D:460 mm; D1 ≈:401 mm; Ba min.:12 mm; Ba |
| PH40F00004F1 KOBELCO Turntable bearings for 40SR-3 | Mass rod end:1.4 kg; C1 max.:22 mm; l7 min.:40 mm; Specific dynamic load factor K:100 N/mm²; G:M 36x3; l4 max.:174 mm; r1 min.:0.6 mm; B:25 mm; dk:47 mm; α:6 °; h1:130 mm; l5 ≈:25 mm; Basic dynamic load rating C:80 kN; d:35 mm; d4 ≈:49 mm; d2 max.:84 mm; Material constant KM:330 |